similar to: Question :: groundstart and loopstart :: Update

Hello Astrites, I was just about to send out a long email about not being able to detect hang-up with my CAC II FXO module on my PSTN POTS lines. I had tried many configurations. I had attached a toner to the line to see if I was getting this "disconnect supervision" signal after hang-up. (toner has a line powered light in the off position) It seemed that I was getting the signal,

I am wondering if anyone could help me figure out how to turn down the volume on all the dial tones, indications, etc.. and especially the call-waiting CHIRP! I don't want to change the txgain and rxgain because they are working at levels that I would like. However, when voice conversations and voicemail recordings are at good levels then the dial tones, busy tones, etc are way too loud.

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port

Hi everyone (Mark, Jim). I am new to the list but thanks to both Mark and Jim, I have being using "asterisk" since summer 2001. I am just updating my version that was a year old. Yes, I know, I got busy with other things like paying bills so I don't have to sleep with the dog anymore. Anyway, one of the frustrations I have been dealing with (keep in mind that my version of

Hi, all I have installed TDM400 with 1 FXS and 1 FXP ports. Now I am goig through documentation on how to configure it. It mentions 3 protocols: Loopstart, Groundstart and Koolstart. Which one do I use? Can someone send me sample zaptel.conf file for Australia? This will save me some time and will be used as a working example. Thanks, Rudolf

Hi everyone, I've just got my X100P card installed and working but there seems to be an issue with hang-up supervision. If I stuff a call out over the X100P card onto the PSTN that's fine. When I hang up the SIP phone the PSTN call ends. If I receive a call from the PSTN, it's answered and everything is ok until the remote party hangs up. Asterisk thinks the call is still active and

Hi there! I'm setting up a connection between Asterisk ver. 1.2.13 and a Harris 20-20 PBX. More less everything went fine, but the problem I have now is when dialing to the Harris PBX, it seems to pick up my call as soon as it reaches it. For example if from the Asterisk outgoing folder I dial an extension, say 100, and play a prompt as soon as it is picked up, the promt is beign played as

I am having a problem using the Adtran 750 FXO quad card with a Groundstart trunk line. I am able to receive calls on the trunk line, however dialing out is not working. The Adtran does not seem to be doing the signaling. Has anyone used the 750 FXO card in Groundstart mode? Any special configuration issues that I should be aware of? Syed Akbar Alico Systems Inc www.alicosystems.com Tel:

hello, I just installed 2 brand new x100p cards into my linux system. Everything compliled and worked fine from the first try. Hoewver the phone lines I will use with this system have groundstart signaling. I have tried to change the zaptel.conf and zapata.conf to use this type of signaling but ztcfg gives me an error every time with the new configuration. Bellow are the config files and the

I bought an Aastra PT480 from digium, but I wanted to see if I could get some more help with this before Monday. Any help would be appreciated. I have the phone connected to the TDM400P card, and I also have the T100P and the X100P in the same box. My problem is, it appears as if the phone and asterisk can't understand each other. The port the phone is connected to always remains

I just picked up a couple CAC Access Bank 1s loaded with FXS that should be arriving shortly. Does anyone have one that they use with Asterisk? If so, would you be willing to shoot me a note with your current configs? I'm not very familiar with CAC/etc, and it would save me countless hours of muddling through .. :) Any others tips you can give me on these banks would be very

Hello, I was wondering if anyone had any ideas to a problem I am having. I have asterisk installed, and running. All extension phones are analog on FXS ports. The phones call each other and even transmit caller ID information but they DO NOT RING. Here is my setup: T400P Quad span T1 card currently connected to a CAC I w/ 12 channels of FXO for incoming lines and 12 channels of FXS for

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1

Hello! Recently I posted a question about an installation I have that was experiencing glare problems. The solutions presented were to use inverse inbound and outbound line groups and to use groundstart signalling. As it turns out, the Sangoma A400D card that is in use does NOT support groundstart. I've confirmed this with a Sangoma engineer and their support staff. I've also read that

I need to know how to setup the data side of the T1 on my Linux Box. I have found information about configuring a PRI and HDLC but nothing about the Frame-Relay type setup for data. The following is information from our T1 provider. Network T1: Framing = ESF Line code = B8ZS Build out = 0-133ft(DSX)/0dB(CSU) Clock = network Pulse-density-enforce = off alarm-option = on alarm-delay = 15

Hello, is there a full guide to what kewlstart is supposed to do with FXO or FXS lines ? is it only applicable to one of the interfaces FXO -or- FXS but not both ? I asked earlier if FXS lines can be made to reverse polarity, and someone else pointed out that the chipset on the FXS ports seems to support it, perhaps the driver in the asterisk zaptel interface module needs to be modified to support

I am having a problem with Red Alarms on X100P cards. The most frustrating thing is I can not duplicate the alarms, therefore am not sure how to solve it. I have read after searching posts and the web that you can try different signaling methods which may help alleviate the problem. There is fxsks (Which I am currently using), fxsgs, and fxsls While reading the Digium site about these different

I am connecting a t100p to a b8zs, superframe, loopstart t1. Previously I've attached to e&m wink and pri lines with no problems; however I seem to be missing something. Should it be fxols in the zaptel.conf (smartjack to x100p) or fxsls? With e&m wink the dnis set was 100, so it was easy to make an extension 100; and it would answer incoming calls. How do you get a loopstart to

Hello, I have an Asterisk 1.2.10, with a TDM with 2 FXO modules, and 2 GSM Nokia32. I configured the TDM with loopstart signalling. For a few days, all works great: Nov 9 09:28:54 VERBOSE[19103] logger.c: -- Called g1/6XXXXXXXX Nov 9 09:28:54 DEBUG[19103] chan_zap.c: Exception on 14, channel 15 Nov 9 09:28:54 DEBUG[19103] chan_zap.c: Got event Hook Transition Complete(12) on channel 15