similar to: Re: Adding an app (Steven Critchfield)

I am in the process of testing out the Cisco ATA 186 to provide analog phone service via VoIP for some of our remote users. I have that working fine and well, but am struggling with another aspect. We already have a large centralized voicemail system, which I would like to use for these users. I can get the call to roll to new the centralized voicemail no problem, but I'd like to provide

After purchasing the Uniden TRU9480 and then the Panansonic 5672, both of which do not have "phone company" compatible FSK/stutter MWI, I finally got smart and found out just which Panasonic phones have this feature. Only the following 5.8G models in their current line have FXO compatible MWI. I purchased the 5771 unit and one remote. I have confimed it does in fact work with Asterisk

I need to setup MWI on a few Aastra 9112's. I've tried doing so in the web interface by setting "Explicit MWI Subscription" to true, but no lights, no stutter tone. Firmware: 1.4.0.1048 Thanks! -- Warm Regards, Lee

I have a quick question... In the previous thread http://www.marko.net/asterisk/archives/0210/0306.html it is mentioned Mark added support for MWI to the chan_zap. Is this in the zapata.conf and if so, if stutter is turned on then the MWI is turned on with it? Geoff

Hi, Using 1.4.26.1 & DAHDI 2.2.0.2, FSK VMWI devices off a TDM840 work fine. With 1.6.1.[45] & same DAHDI, instead of the FSK spill I get a line polarity reversal. Stutter dialtone is generated as expected. Has anyone else seen this? Is there anything special I need to do for 1.6.1 to make FSK MWI work? Thanks, --Barry

Let post this question.. Because I must be real slow... The following is my config on this... group=1 context=default signalling=fxs_ks channel => 1 context=local signalling=fxo_ks callwaiting=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes echocancel=yes echocancelwhenbridged=yes relaxdtmf=yes rxgain=1.5 txgain=1.5 immediate=no musiconhold=default usecallerid=yes

I recently set up Asterisk with an Adtran TA750. All is well except the phones do not show the MWI. I have configured zapata.conf properly, as all phones will receive a stutter dial tone if there is a message waiting in it's assigned mailbox. Does anybody know how I might fix this problem? Thank you for your time __________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free,

My grateful thanks to whoever can guide me in implementing this... I have a need to place calls via Asterisk Manager Protocol to a legacy PBX and twiddle its MWI lights. By some means I get notified that an MWI light has to be changed. Via AMP: 1. Send an ORIGINATE command honking up an incoming port on the PBX via a TA804. a. I presume that the TA804 should be a SIP channel. yes/no? b.

Does anyone have personal experience with a 5.8gig wireless phone (system) that has an MWI that WORKS with asterisk via fxs (in my case spa3k) generated MWI. I know the spa3k does stuttered dialtone but not sure if it generates FSK MWI. I see some that state they do but I also see reviews that say they don't. Doug

I have many remote locations that dial into a central server to retrieve voicemail via IAX. Outbound calls are handled as SIP calls from a Snom to a local (to them) Asterisk server that dials the main server thru IAX. I have trained them to check their voicemail via the emailed WAV file, however some of them are, how shall I put it, idiots*, and insist that they *have* to have the MWI indicator

I think I have something misconfigured regarding voicemails. They work great, I have this setup: Sip.conf [ext1] Context=phones Mailbox=201 Voicemail.conf [home] 201,password,name,email@mail Voicemail delivery and all works great but when I check sip extension ext1 (analog phone using a Granstream ATA 286), the stutter tone signaling message waiting does not work. Anything wrong with

Hello, it is possible to get MWI working with Grandstream and Asterisk? Thanks. -David

Besides email notification, is there another way to get asterisk notify the user that they have a message? Example: Some analog phones have a blinking light that lets the user know that they have a voicemail message. Is asterisk capable of doing this?

Hi.. I am about to replace my aging Nortel Venture system with an Asterisk system and 6 Polycom IP 501 phones, and a couple sipura 841's for less used areas. We have 3 phone lines here. One is SBC, one Vonage, and one Voipjet... One hangup is that I can't figure out how to pass through a voicemail waiting indication from SBC. This is important because my wife and her family all

Anyone out there using AT-320 phones with IAX? Can you get MWI to work? I can only get it to work with SIP. Also, I note that (on the phone) dtmf has to be set to "sip info" or dtmf doesn't seem to work at all (when the phone's under SIP). Sounds like the IAX firmware isn't all that finished? Eric.

We are using Bellsouth 8867 phones on our TDM400B FXS lines (asterisk-1.0.3). It has a "Voicemail" light, which appears to be MWI (according to the manual it works with voicemail from the telco that sends a FSK signal). The dialtone stutters when a line has voicemail, so I know that I have the mailbox setting right in zapata.conf, but the light doesn't go on. I am also getting

Hey all...I'm trying to find a phone that will support multiple MWI so that I can have a shared central phone with say 4 users who can see visually that hey have messages waiting. Is there any phone that will do this possibly by re-assigning a soft-button? Can the Polycoms do this since those seem to be the phone of choice these days? Thanks!

Hello, I faithfully followed the instructions from: http://www.voip-info.org/wiki-Getting+MWI+on+Polycom+Phones+to+work+with+Asterisk but still the message waiting indicator doesn't flash when a message is waiting. There is a brief intermittent chirp but nothing more. Using latest firmware 1.4.1 Thanks for your suggestions,

While I know this is not a true asterisk problem, I figure someone where may know. When you click on Messages and it gives you the count of Urgent, New, etc. How can you make the phone gather that information? For example, my phone shows me there is an e-mail. It also sends an e-mail. Yet, when I click on message before I connect to the contact center, it doesn't have any counts. Here is

Howdy I have a question regarding support for picking up when the telco sends a MWI message. My client's setup is a small office with three incoming lines on a TDM400P with iaxy's and a Grandstream as extensions. I am using CVS Head from yesterday. (I was resolving a different issue.) Since they only have two voice lines, with the third as a fax, I am using voicemail from the telco.