Displaying 20 results from an estimated 1000 matches similar to: "ISDN4Linux + Asterisk and Europe"
2003 Jun 17
3
Voice linmodems and Asterisk PBX
Hello group,
Just got this reply from Sasha @ Smart Link, a soft modem chipset
company with a very nice attitude towards Linux. BTW, You can check the
status of most modem chipsets and Linux support here:
http://www.idir.net/~gromitkc/dips/roster.html
The good news is that the current 2.7.x series supports voice commands
and is full duplex, but can only work with one modem. This issue will
2003 Apr 07
6
ISDN4Linux problems
Hi,
I try to use ISDN4Linux drivers with Asterisk.
In modem.conf i put /dev/ttyIO.
Everything is OK when i lauch asterisk but, when i call Asterisk nothing happen.
Someone can help me ?
Rattana
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030407/13e78d8e/attachment.htm
2003 Jul 24
2
isdn4linux
Hello All,
I was just after a few pointers. I have just setup my Redhat 9 linux box
with asterisk. Internal SIP call working fine.
My Eicon ISDN card turned up today so - plugged it in and went through
the modem.conf. It reports unable to open /dev/ttyI0
The problem is I have never used ISDN with Linux - let alone a telephony
app - and I have no idea even where to start. Some pointers
2004 May 05
7
* & ISDN-BRI-PTP & DID & ISDN4Linux does not show incoming number
Hi,
I am using Asterisk on a DSS1 ISDN-BRI with ISDN4Linux (and a Fritz Card PnP).
The ISDN-BRI is in PTP-Mode (Point to Point "german: Anlagenanschluss")
which is enabled within I4L with "hisaxctrl fcpcipnp0 7 1".
Everything works fine except that I can not see the called number/MSN
of incoming calls within Asterisk and because of this I can not route
incoming calls
2004 Apr 21
1
one-way audio and isdn4linux
Hi,
Apologies in advance for the lengthy email.
I'm new to asterisk and have trouble with isdn4linux.
The setup is very basic like this:
winxp ------- asterisk -------- winxp
x-lite | x-lite
|
pstn
The hardware involved is:
Compaq EVO with RH9/kernel 2.4.20-30.9.
Fritz!Card PCI v2
Asterisk CVS-04/17/04-21:36:18
Basically
2003 Nov 10
1
ISDN (isdn4linux) DDI
Hello all,
does anybody have experiences with DDI on ISDN BRI? I would like to
order DDI with 10 or 100 numbers from telco company, and use DDI
numbers for direct calling SIP/H323 clients. But I don't know if
Asterisk supports it, in archive I found only one answer about it, and
I'm not sure. I am going to use it with isdn4linux card.
Maybe DDI is called differently in other countries,
2004 Apr 25
1
no audio using isdn4linux channel
I'll try again using my subscribed address... Apologies to the moderators...
---
Hi All,
I've successfully got SIP and IAX2 working on Asterisk using X-Lite as a
SIP phone and talking to a remote Asterisk over IAX2 using G729.
I'm now trying to get an ISDN BRI connection working. I have a Traverse
NetJet card (http://www.traverse.com.au/) which I currently have working
with
2004 Nov 27
1
isdn4linux delay
I have a weird problem and I cannot put my finger on it.
I hope somebody can help me out.
Incoming and outgoing calls via the internet go perfectly well.
Calls that originate from a SIP or AIX client on the local LAN (100 Mbx)
and terminate via a Winbond BRI often (not all of the times, but most of
the times) are having a (about) 5 second delay starting from when I say
something until the
2005 Feb 12
3
Initializing two ISDN cards in isdn4linux
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hello!
After LOTS of research on this list and internet in general I managed
to get
an old Teles PCI card working with Asterisk throught ISDN4Linux.
No echos, no delays, simply perfect -- electronic poetry ! :)
eheheheheh
I just didn't get it to work with CAPI and "chan_capi" but, since
isdn4linux
is doing such a good job, I'll
2005 Jan 21
0
Caller id with isdn4linux
hello
Sorry for my poor english...
A have probleme with callerid with isdn4linux
I am using diva pci 2.02 passive card,
Asterisk 1.0.4 (i have tested all releases)
Fedora core 2
Zaptel card
All work great but i have not the caller id.
I have trace chan_modem_i4l.c, and callerid id string send by isdn4linux is
ok
(CALLER NUMBER: XXXXXXX
RING/YYYYYYY and so on...)
I never could install isdn
2003 Jun 16
0
newbie: isdn4linux and BRI (FRANCE)
hi
i would like samples examples to configure with isdn4linux
i have hisax card : "gazel" and an ISDN(BRI) line (2 channels B and 1D)
In fist time i'll use "sjphone" only
Perhaps there is french people on this list who can help me to do first
steps with "Asterisk"
thanks
2004 Oct 07
0
ISDN4Linux early call progress tones & announcements from the PSTN
Hello,
I would like to ask if anyone has solved the problem with
Asterisk+ISDN4Linux cards, where there are no call progress tones or
announcements from the PSTN when we dial ouot through the i4l card.
For the moment, if we don't inject the r option in the Dial command,
there is only silence during the call negotiation...
Using Asterisk RC2 with Eicon passive PCI 2.01 card...
Thanks for
2004 Dec 29
0
ISDN4Linux Incoming calls
Hi everybody !
I've a Pentium IV with a USR ISDN PCI Card W699. Card
I've installed asterisk 1.0.0 and it's working fine with outgoing call to
POTS
But it never answers to my incoming call from POTS and I don't understand
why.
I tested the modem also with the minicom utility and I never saw the "RING"
status
It seems that the modem didn't know somebody is
2005 Feb 22
0
PSTN tones with ISDN4Linux
Hi all,
I'm playing with Asterisk and I've already configured all needed .conf
files.
It works quite well, but now I need your help to tune the system: when I
place a call from a softphone to the PSTN, I can't hear directly Telco's
tones and I can't use its services, e.g. a mobile's answering machine.
I don't know if I have to modify the dialplan or if it depends on my
2005 Jan 21
1
Intermittent breakage with the ISDN4Linux modem driver
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
I'm having some problems using the asterisk modem driver with an
ISDN4Linux card (AVM Fritz). (I realise that it's better to use CAPI,
but unfortunately this card doesn't have any CAPI drivers).
Every so often the ISDN just stops working (it neither dials out nor
accepts incoming calls). Trying to dial out just logs:
--
2004 Jan 05
1
CLIR and isdn4linux
hi
I have a passive isdn port configured in modem.conf
in extention.conf i use this two channel (ttyI0 and ttyI1) with the string:
exten => _NXXXXXXXXX,1,Dial,Modem/g1:${EXTEN}|60|r
how can i hide my msn?
is it possible to activate the clir with the @ before the ${EXTEN}?
thanks
Cristian
2004 Aug 19
1
Isdn4Linux and DTMF
Hello all,
I currently have an Eicon Diva Client isdn card using i4l. Outbound
dtmf doesn't work (and never has), but there has been an annoying
problem with false dtmf detection in calls (that could be triggered
easily by blowing into the receiver on the remote end).
I looked through the list and found two patches that need to be
applied - 1 to isdn_tty.c in the kernel, and another to
2004 Sep 07
1
Asterisk + NetJet (ISDN4Linux)
Well, it has been a long time since I used my NetJet S cards with
asterisk (moved to the quad PRI card) but I am trying to get this
working again for home use.
Basically, what I am using is this:
Linux 2.6.8.1:
config lines:
# ISDN subsystem
CONFIG_ISDN=y
# Old ISDN4Linux
CONFIG_ISDN_I4L=y
# CONFIG_ISDN_PPP is not set
CONFIG_ISDN_AUDIO=y
# CONFIG_ISDN_TTY_FAX is not set
CONFIG_ISDN_DRV_HISAX=y
2004 Jun 07
1
isdn4linux, NETjet, chan_modem help needed
I'm trying to get a basic Asterisk configuration together for ISDN incoming
/ outgoing calls. I have two Cisco 7905g phones working (at least talking to
each other) and have purchased a NETjet-S PCI ISDN card for routing calls to
/ from ISDN.
The state I've managed to get it to is:-
-- Executing Ringing("SIP/PHONE2-d557", "") in new stack
-- Executing
2004 Apr 07
0
Struggling with ISDN4Linux and Asterisk config
The card is an ASUSCOM ISDNLink PCI (passive) and the circuit is from
Qwest (in the US). I will be using this circuit only for voice (I'm
doing this because of the poor quality of my POTS lines).
I've compiled Hisax (as a module) into my 2.4.25 kernel, and with
'modprobe hisax type=35 protocol=4 id=hisax' I get the following:
Apr 7 10:34:24 dev kernel: HiSax: Linux Driver for