similar to: Asterisk 1.6.0-beta4 Released

Hello, I am implementing a small ACD system on Asterisk 1.6.2.17.2 I need help with ChannelRedirect. I have a caller connected to an agent. The agent may request additional help by consulting another department. I can't use manual process with blind or directed transfer as the agent have many different numbers to dial. The message with the proper dial number is coming from the host. I got

Hi all I don't know what went wrong but i no longer seem to be able to compile asterisk. I first do : cd /usr/src/dahdi-linux-2.1.0.4 make clean ; make all ; make install cd /usr/src/dahdi-tools-2.1.0.2 ./configure ; make clean ; make all ; make install ; make config So far.... so good but then when i do : cd /usr/src/asterisk-1.6.0.6 make clean ; ./configure ; make all ; make install i

Hello, In my scenario, the asterisk machine is installed behind a CISCO mediaGW in order to be able communicate with the PSTN. Asterisk is configured to use T.38 to send and receive faxes. I'm trying to receive a fax from a fax machine located in the PSTN. Apparently everything goes well: the fax machine says the transmission was successfully completed, and the fax file is successfully

Hi, With 0.0.6pre3: # ./build.sh CMake Warning (dev) in CMakeLists.txt: No cmake_minimum_required command is present. A line of code such as cmake_minimum_required(VERSION 2.6) should be added at the top of the file. The version specified may be lower if you wish to support older CMake versions for this project. For more information run "cmake --help-policy CMP0000".

2009/2/26 Olivier <oza-4h07 at myamail.com> > I must add I tried spandsp0.0.6xxx as a warning message advised me to do so > (using 0.0.4 would be ok for me but current trunk doesn't allow this > anymore, it seems). > > > 2009/2/26 Olivier <oza-4h07 at myamail.com> > > Hi, >> >> With 0.0.6pre3: >> # ./build.sh >> CMake Warning (dev)

Hi, I'm struggling with a feature in my home phone setup. I have several phones using both SIP and SCCP. What I try to do is to create a dynamic feature that works similar to the blindxfer feature built into Asterisk. What I want is the possibility for the called part to push a number sequence (for example *#) to redirect the callee to a fixed extension or (for example *123#) to redirect the

Hey guys I was hoping I could get a few pointers on a problem I have been trying to debug for the last couple of months regarding asterisk AGI scripts and unexpected termination. I have this agi script that accepts incoming faxes using RxFax on the latest asterisk 1.4 branch. Its written with perl and it works fine except for one line that causes the entire script to terminate unexpectedly. The

You now need to compile and install SpanDSP-0.0.6pre3 at least (AGX has been changed). After you've done that - try AGX again. HTH -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Olivier Sent: 11 March 2009 06:16 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [asterisk-users]

Hi, I've installed spandsp-0.0.4pre16 With this: cd ~ svn co https://agx-ast-addons.svn.sourceforge.net/svnroot/agx-ast-addons agx-ast-addons<https://agx-ast-addons.svn.sourceforge.net/svnroot/agx-ast-addonsagx-ast-addons> cd agx-ast-addons/trunk ./build.sh I've got this: CMake Error in spandsp-0.0.4/CMakeLists.txt: Cannot find source file "app_fax.c". Tried

I downloaded spandsp0.0.6pre17 I download http://sf.net/projects/agx-ast-addons for app_txfax and found trunk/app_fax to be newer so I used that. spandsp compiled fine. app_fax compiled when loading I get: [Apr 5 08:55:54] ^[[1;31;40mWARNING^[[0;37;40m[7505]: ^[[1;37;40mloader.c^[[0;37;40m:^[[1;37;40m433^[[0;37;40m ^[[1;37;40mload_dynamic_module^[[0;37;40m: Error loading module

Thanks Brian, and thanks again for the included definitions <grin> - that helped too. Your comments are really helping clear many questions. I suppose our intensions are to become an IXC. So if my local carrier is sporting old technology, they'll provide TDM services. So if I understood you correctly, the "in-band signaling" is typically SS7, and the alternative is typically

Receiving a fax with 1.6.1: == Spawn extension (incoming-pstn-line, fax, 1) exited non-zero on 'DAHDI/4-1' -- Executing [fax at incoming-pstn-line:1] NoOp("DAHDI/4-1", "Fax Detected") in new stack -- Executing [fax at incoming-pstn-line:2] Goto("DAHDI/4-1", "incoming-fax,s,1") in new stack -- Goto (incoming-fax,s,1) --

The Asterisk.org development team has released Asterisk-addons version 1.6.0-beta2. This release contains the following improvement, along with some other minor bug fixes. - 11614, Updated app_fax to allow termination and origination of faxes over T.38 The full list of changes is available in the ChangeLog. The release is available for download from http://downloads.digium.com.

The Asterisk.org development team has released Asterisk-addons version 1.6.0-beta2. This release contains the following improvement, along with some other minor bug fixes. - 11614, Updated app_fax to allow termination and origination of faxes over T.38 The full list of changes is available in the ChangeLog. The release is available for download from http://downloads.digium.com.

Using spandsp-0.0.6-pre17, SendFax on 1.6.1.18 and ReceiveFax on 1.6.2.8. Sip.conf on both sides has t38pt_udptl = yes. -- Executing [s at fax-tx-test:3] SendFAX("SIP/side-sip-00000009", "/var/spool/asterisk/fax/20091113_1455.tif") in new stack [Mar 20 17:05:34] WARNING[6433]: app_fax.c:178 phase_e_handler: Error transmitting fax. result=49: The call dropped

Hello, I'm working on some dialplan rules to pull multiple users into a conference call. I have some fairly straightforward rules which start up a new MeetMe conference, allow escape with the * key to invite more users, then use a features.conf sequence to bring the new user into the conference with ChannelRedirect. The problem I'm running into is the time in the MeetMe conference

Hi, i am using the n-way-call dialplan solution found on voip-info. i have added its entry in applicationmap of features.conf file. the problem is......its not working. to activate the n-way call i dial *0 but nothing happens. i have played around with dtmf and codec settings but no success. the extensions and sip configuration is below if you want to have a look. I dont have any clue why its not

hi folks. i recently upgraded asterisk to 1.6.1.17(from 1.2) and i'm having problems with fax. after receiving fax with the ReceiveFAX app. everything seems ok. the .tiff file was there, phone line seems to hang up. then asterisk will crash. any ideas? also i looked in the log file. this is what before it crashed: [Mar 8 12:12:12] WARNING[30115] app_fax.c: WARNING T.30 ECM carrier not found

To provide a reliable fax solution for users connected to a Asterisk 1.6.2.6 server i have tested a few T.38 capable ATA's: - Patton M-ATA - Grandstream HandyTone 486 - Fritz!Box 7170 I have tried Asterisk 1.6.2.6 compiled with SpanDSP-0.0.6pre17 and also Asterisk 1.6.2.6 with Fax for Asterisk installed. These Asterisk servers are connected to a Cisco PGW 2200 + AS5400XM. Sending fax

I'm trying to capture faxes on 1.6.1-beta4. AFAICT, app_fax is working OK. I'm then using fax2mail to send the fax. That wasn't working, so i posted for help using the System() cmd, since fax2mail did work from the command line. But now I realize it's fax2mail and mime-construct itself. I set up a fax-test context: [fax-test] exten=>666,1,NoOp( fax-test )