similar to: Tracing sieve execution

Hi Timo, I've just tried to convert my v1.2 configuration to a v2.0 configuration. Below a few obsolete warnings, among others "mail_executable has been replaced by service { executable }", was an interesting error: "doveconf: Error: duplicate listener: 198:" The broken parts of the converted configuration: # 2.0.beta4 (84ffb38839b9): /etc/dovecot/dovecot.conf # OS: Linux

I forked the wiki to http://wiki1.dovecot.org/ is the old docs for v1.x http://wiki2.dovecot.org/ is the new docs for v2.0 For now wiki.dovecot.org points to wiki1, but once v2.0 is released I'll change it to point to wiki2. I symlinked the user directory, so users should stay synced between the wikis. The main reason for wiki2 is to be able to describe Dovecot v2.0's actual behavior

Hi Timo, after changing the mail_executable in the imap {?} section I have to restart Dovecot v1.2.rc5, otherwise the changes are not accepted. With Dovecot v1.1.x (tested with v1.1.11 and v1.1.16) it's enough to send a SIGHUP to the dovecot process. Regards, Pascal -- The trapper recommends today: c01dcofe.0916521 at localdomain.org

Hi all, since many dovecot/pigeonhole versions I have an error: Mails are delivered into wrong folders if the foldername contain a german umlaut. ( ?, ?, ? ) setup: dovecot-2.1.1 / pigeonhole-0.3.0 postfix deliver to dovecot-lda .dovecot.sieve contains this: require

I know that this is technically not a Dovecot problem; however, I was wondering if anyone knew if 'sieve' had been updated with the ability to 'forward as attachment' a received document. I believe it has the ability to forward a document; however, I need the ability to forward it as an attachment if possible. Also I believe, somewhat due to my asking for them, that sieve exits

Hi Timo, doveadm reports errors for \Noselect mailboxes. What I have: 1 LIST "" * * LIST (\HasNoChildren) "/" "Templates" * LIST (\HasChildren) "/" "INBOX" * LIST (\Noselect \HasChildren) "/" "INBOX/Lists" * LIST (\Noselect \HasChildren) "/" "INBOX/Lists/vmm" * LIST (\HasNoChildren) "/"

Since the changesets: http://hg.dovecot.org/dovecot-2.0/rev/9bec70f26637 http://hg.dovecot.org/dovecot-2.0/rev/75b48fa3aec4 there is another problem. A `dovecot stop`, while auth and auth -w are still running, logs: Nov 12 03:17:00 master: Warning: Killed with signal 15 (by pid=31656 uid=0 code=kill) Nov 12 03:17:00 auth: Error: read(anvil-auth-penalty) failed: EOF Nov 12 03:17:00 auth:

Using Postfix with Virtual Users/Virtual Domains, I have configured it with a wild card entry; i.e., "*.mydomain.com" This works fine in Postfix; however, using Dovecot for delivery is causing the message to bounce since Dovecot does not have an entry in the "user passwd" or "userdb" file. I want to store the catch-all addresses in a separate mailbox. Can I use sieve

I am not even sure if this is possible. I cannot find an example of it anywhere. I am in the process of setting up a "plus" addressing system. The addresses would be addresses to accounts like <sales+USERNAME at domain.com>. there are presently 50 such names in sales. This is the one line entry I presently have in the sieve script: if envelope :detail "To"

Greetings all, I have a OpenBSD /Dovecot server at home running and sending / receiving email "internally" without issue.. Recently, I set up the same at our Parish, but one of our users wants to get their email externally. The user can read their email but has to "send" via the local ISP server.. The problem After much searching I have not found an answer to my question. I

Hi, using LMTP, is it possible to disable the addition of the Delivered-To header to messages? Micha Krause

Hi all, Got a question on configuring dovecot, I'm still new at this so I might be doing this all wrong. I want dovecot to authenticate the mail client using CRAM-MD5 so I've setup the config in dovecot.conf: auth default { mechanisms = cram-md5 passdb sql { # Path for SQL configuration file, see doc/dovecot-sql-example.conf args = /etc/dovecot/dovecot-sql.conf

Im sendding messages to the list and they do not show up. its just a test, please ignore Regards, Carlos Xavier.

/* sorry, my english is bad :-( */ There's error i found while compile dovecot 1.1.16 Compiling run on Slackware 12.2 (fresh install) Error in src/dict/main.c line 85 and line 102 dict_drivers_register_all(); and dict_drivers_unregister_all(); I know C so little, and try to add these line to dict.h void dict_drivers_register_all(void) void dict_drivers_unregister_all(void) After

I don't know if this tool already exists, or if not how difficult it would be to implement, but the following is an excerpt from the man page the developer needs to write ;) - "imapcopy", a command-line utility that connects to a given IMAP account and copies the mails to a second IMAP account. This is accomplished using only IMAP commands and may be used with any IMAP compliant

Is there a tool to recover space used by refcount=0 messages in mdbox storage files? The wiki talks about it but it isn't clear where the tool is. Regards, Bill

I just downloaded 1.2.11 and compiled from source including mysql support and using default directory locations. I walked thru the included example conf file and tweaked it out and get an invalid configuration file. I trimmed out all of the commented sections to make the non-default config super easy to navigate during troubleshooting. Remaining config which gives an error of

I'm running postfix 2.6.2 and dovecot 2.0.9, and I've just switched to delivering mails to dovecot via lmtp. It looks like the Delivered-To: header is slightly different - it doesn't seem to include the +extension? Is this intentional or does the +extension somehow get in the way? /Per Jessen, Z?rich

Hi, i'm trying to configure imap_stats like it's documented in the wiki: http://wiki2.dovecot.org/Statistics. But as soon as i activate the imap_stats plugin i get the following error message trying to login via imap: dovecot: imap: Error: Can't load plugin imap_stats_plugin: Plugin stats must be loaded also (you must set: mail_plugins=$mail_plugins stats) But the stats plugin

Hi, I get "Unknown scheme: BLF-CRYPT" messages if I try to use Blowfish-encrypted passwords, even though it is supposed to be supported. I'm on 2.1.7, Debian Squeeze backports. Do you have any information whether Blowfish is supported with Debian Squeeze crypt(), or is there any other knobs I can turn on to make this algorithm available? Thanks, Kristof