search for: fe23

...2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 78:2b:cb:23:21:4c brd ff:ff:ff:ff:ff:ff inet 192.168.5.205/24 brd 192.168.5.255 scope global eth0 inet 192.168.5.217/24 brd 192.168.5.255 scope global secondary eth0 inet6 fe80::7a2b:cbff:fe23:214c/64 scope link valid_lft forever preferred_lft forever ... Then I add a new route via a network gateway but I want the route to use the secondary address as a source. # ip route add 11.11.11.11 via 192.168.5.148 src 192.168.5.217 And the ip route show command shows that it knows the s...

hello, i met a problem in configuratiion of ipv6 gw in my box i install centos 6.3 (64 bit) on my boxs, which have four netcard. i use a straight-through cable to connect centosv0:netcard-2 and centosv1:netcard2 the topology is this: client c(windows xp) <-->centosv0:netcard-3 <--> centosv0:netcard-2 <---> centosv1:netcard-2 <---->centosv1:netcard-2 <---> client d

This is ifconfig on openbsd box: fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 I think this output shows that the fxp0 interface is on simplex mode. The voice degradation I referred was by using xlite soft phone. I open 2 line similtaneously and dial to FWD and back to my incoming extension. Xlite is runnning on a w2k box with realtek 100M nic in auto mode. I can

...ID: <20200226115708.GH13686 at intel.com> References: <20200219203544.31013-1-ville.syrjala at linux.intel.com> <CGME20200219203620eucas1p24b4990a91e758dbcf3e9b943669b0c8f at eucas1p2.samsung.com> <20200219203544.31013-5-ville.syrjala at linux.intel.com> <0f278771-79ce-fe23-e72c-3935dbe82d24 at samsung.com> <20200225112114.GA13686 at intel.com> <3ca785f2-9032-aaf9-0965-8657d31116ba at samsung.com> <20200225154506.GF13686 at intel.com> <20200225192720.GG13686 at intel.com> <CACRpkdZk9QEy+Kzkmy4BXiHB+aq9hprf=dmA_-R23yqH3NCt1g at mail.g...

...<BROADCAST,SIMPLEX,MULTICAST> mtu 1500 ether 00:0e:a6:8a:88:10 media: Ethernet autoselect (none) status: no carrier xl0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 options=9<RXCSUM,VLAN_MTU> inet6 fe80::250:daff:fe23:4e56%xl0 prefixlen 64 scopeid 0x2 inet 10.11.12.3 netmask 0xffffff00 broadcast 10.11.12.255 ether 00:50:da:23:4e:56 media: Ethernet autoselect (100baseTX <full-duplex>) status: active plip0: flags=108810<POINTOPOINT,SIMPLEX,MULTICAST,NEEDSGIANT> mtu 1...

...inet6 ff02::1/128 scope global valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:c0:9f:23:a8:44 brd ff:ff:ff:ff:ff:ff inet 192.168.100.1/24 brd 192.168.100.255 scope global eth1 inet6 fe80::2c0:9fff:fe23:a844/64 scope link valid_lft forever preferred_lft forever inet6 ff02::1:ff23:a844/128 scope global valid_lft forever preferred_lft forever inet6 ff02::1/128 scope global valid_lft forever preferred_lft forever 4: sit0: <NOARP> mtu 1480 qdisc noop link/sit 0.0...

...06/27 19:44:00.290106, 6] param/loadparm.c:7155(lp_file_list_changed) lp_file_list_changed() file /etc/samba/smb.conf -> /etc/samba/smb.conf last mod_time: Wed Jun 27 19:43:02 2012 [2012/06/27 19:44:00.290526, 2] lib/interface.c:340(add_interface) added interface eth0 ip=fe80::2c0:9fff:fe23:dcbb%eth0 bcast=fe80::ffff:ffff:ffff:ffff%eth0 netmask=ffff:ffff:ffff:ffff:: [2012/06/27 19:44:00.290672, 2] lib/interface.c:340(add_interface) added interface eth0 ip=192.168.1.7 bcast=192.168.1.255 netmask=255.255.255.0 If u see, nothing really bad, I had other server running the same versio...