search for: downlinks

Hello all, I have browsed archives and real all available HOWTOs, but I still have a few doubts. My set up is a router, as below. LAN(100MB)-------------(eth1)Linux-Router(eth0)---------------WAN(2MB/512) My aim is to cotrol both uplink and downlink bandwidth. For uplink control, I will use HTB on WAN interface. For downlink, I plan to attach HTB on LAN interface(both egress/outgoing). No

Hi there good people, I''m a newbie in what concerns running Linux on machines other than desktops, so I need help from all you gurus out there :-) I have Linux installed on an old computer (Winchip C6, Pentium clone), acting as a router/firewall for two other computers. Both these machines are connected to the firewall via a dedicated ethernet card each, on different subnets,

I have been testing wondershaper 1.1a with htb. DOWNLINK=2304 UPLINK=1024 DEV=wlan0 No other changes have been made, except to comment out the 2 lines to allow the script to run. When I do a speed test from sites like www.toast.net/performance, I only get speeds equal to my UPLINK speed. I expected a speed closer to the DOWNLINK. Am I missing something here? TIA, -- -Wes Hegge Technical

I am currently using the ultimate-tc script from http://lartc.org/howto/lartc.cookbook.ultimate-tc.html and I want to make sure that internet radio packets (mp3 streaming audio) will always get through no matter what. I have added some iptables commands like this: iptables -A OUTPUT -t mangle -p tcp --dport 8000 -j TOS --set-tos Minimize-Delay iptables -A OUTPUT -t mangle -p tcp --sport 8000 -j

Hi, When i do ''wshaper start'' the interface i have defined stops routing traffic for some reason. It resumes routing when i do ''wshaper stop''. I''m using debian stable (3.0 woody) with debian''s default 2.4.18-686 kernel. When I run the script I get no errors, and when I do a ''status'', everything looks correct. Can ANYONE

Hi ! I wanted to shape my analog modem connection so I took these two lines from the ''wondershaper'' script: tc qdisc add dev $DEV handle ffff: ingress #tc filter add dev $DEV parent ffff: protocol ip prio 50 u32 match ip \ src 0.0.0.0/0 police rate ${DOWNLINK} burst 10k drop flowid :1 with DEV=ppp0 and DOWNLINK=24kbit. But, when I activate it, nothing comes back from the

Hello all, I am providing broadband service through DVB circuit. I have 4KB uplink and 32KB downlink. I want to share 32KB downlink bandwidth among 192.168.0.0/24 (20 users in this subnet i.e 192.168.0.2-192.168.0.22)subnet where each user will get 2KB to 6KB bandwidth. And from 4KB uplink bandwidth each users will get only 1KB to 2KB bandwidth.

hey guys i am regulating the traffic to & fro by my network through a linux gateway , its behaving strange. i regulated Downlink to 2Mbps & UPlLINK to 500Kbps. both perform well when those are done independent i.e. one at a time but when i do both from a client system ..the downlink however continues at 2mbps but the uplink falls down to 100kbps? is something wrong with my script or

Hi folks, I read the fantastic LARTC How-to and after that i tried to limit one host in my LAN for both down-and upload bandwidth usage. I took section 15.9. and added uplink-limiting as I understood it from the previous chapters. Unfortunately it doesn''t work. I ran the script and went to the specified PC, started a download, and watched the rate. The rate was always about 2000 kbit/s,

Hi, I am connected to two DSL providers (DSL 1 - 1Mbps downlink/384kbps uplink and DSL 2 - 2Mbps downlink/512kpbs uplink) I would like to only allow ftp, pop3 and http via the DSL 1 and only smtp, ipsec and pptp via DSL 2. How can I do so? Can I use iproute to route these protocols? Below is my ip routing: - # DSL 1 ip route add 2.2.2.208/30 dev eth0 src 2.2.2.210 table 1 ip route add

helo again. I think this question i am asking is worth: we know that pppoe-server creates a pppX device on each connection done to it. So, when i have to shape, i have to shape each pppX connection device on itself alone. What i know is that the borrowing method on one device by itself, e.g. ppp0, alone using HTB or the like. this means that i have to create for another device, e.g. ppp1,

Hello, I am trying wondershaper-1.1a on a friend''s pppoe connection on her Linux box. There are a few things I don''t understand. 1. She has pppoe connection so should DEV=eth0 or DEV=ppp0 ? 2. Her ISP just says on her payment bill that the speed is 128kbps, but doesn''t mention any downlink/uplink speed, so in that case what should be, DOWNLINK= and UPLINK= ? 3. She

Hi, I have a question about policy filters. All I want is incoming traffic being restricted to a specific rate. At the moment, I get way lower rates than specified. So far, I did use a filter much like Wondershaper does: tc filter add dev $DEV parent ffff: protocol ip prio 50 \ u32 match ip src 0.0.0.0/0 \ police rate ${DOWNLINK}kbit burst 10k drop flowid :1

Hello, I''m trying to configure several wireless routers with QoS support. The idea is to implement differentiated services so that VoIP traffic gets the maximal priority, then video, control traffic, interactive data traffic and best-effort traffic. I have seen that CBQ used to be chosen as qdisc for implementing bandwith share in DiffServ but now HTB is preferred because it is

Hi, How can I set equal bandwidth of 512kbit downlink and 256kbit uplink for every single IP address of 254 IP addresses I have in my LAN? Regards, ro0ot

Hi, all I''ve got problems with tc qdisc ingress. I''m using vanillia kernel 2.6.14.4 patched with http://www.ssi.bg/~ja/routes-2.6.14-12.diff, and iproute2-2.6.14-051107. i am using ingress to limit incoming traffic : (DEV is eth1 / DOWNLINK is 7700) # attach ingress policer: tc qdisc add dev $DEV handle ffff: ingress # filter *everything* to it (0.0.0.0/0), drop everything

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! when I activate wondershaper on my dsl connection (pppoa vc mux), i get three errors: # sh -x /usr/sbin/wshaper ppp0 + /usr/sbin/xmlstarter setenv tc_downlink + DOWNLINK= + /usr/sbin/xmlstarter setenv tc_uplink + UPLINK= + [ -z ] + cat /proc/avalanche/avsar_modem_stats + grep Connection Rate + awk {printf("%d", $8)} +

Hi, I''m really new to traffic shaping and try to implement the wshaper.htb script. I have a linux box that serves as vdr, mldonkey, samba, apache and mailserver (imap), connected to my LAN with 100mbit. I''m connected to the inet via adsl with a hardware router/firewall, got 384k downlink 64k uplink. When I have mldonkey running, imap (via Outlook) gets *very* slow (mails with

i am assigned a network to replace its "Windows server with ISA caching proxy" with another "debian linux with squid proxy" with both "linux" and "ISA" are completely differnet boxes. i am using linux 2.6 kernel since the linux server has SATA hard disks . the network has downlink with a penta@net DVB card for down-link ; then it''s connected

tc class add dev $DEV parent 1: classid 1:1 htb rate ${UPLINK}kbit burst 6k tc qdisc add dev $DEV handle ffff: ingress tc filter add dev $DEV parent ffff: protocol ip prio 50 u32 match ip src \ 0.0.0.0/0 police rate ${DOWNLINK}kbit burst 10k drop flowid :1 why does the download is being sent to class 1 which is limited by uplink ? why the rate is being mentioned in filter and in class ?