search for: daughterboard

Hello All, I saw an add in my latest Linux Journal advertising Sangoma's new "AA series" of FXO/FXS analog cards with on-board echo cancellation, but I can't find any information at all on them. Even the link given in the advertisement is a dead end as far as I can tell. Anybody else seen/heard anything about this? -Seth

Hi, I have a system that is experiencing profound echo on channel 4. I switched POTS lines around to see if it was the line or the port and it is still a problem on port four. Has anyone ever seen this before? Thanks, Steve -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have installed FC3 using the notes from lesnet http://www.voip-info.org/tiki-index.php?page=Asterisk+Fedora+Core+3 It worked very well, worked first time. My configuration consists of: (1) TDM400P w/ 2 FXS daughterboards and w/1 FXO daughterboard I use yum update to update my installation. After the update and reboot, I attempted to recompile zaptel, Zapata, libpri, asterisk. No errors, when I try and start zaptel with /etc/init.d/zaptel I get: Loading zaptel framework: [ O...

...n be pushed into the addons directory. >2) An IAX2 hardware device Any Day Now(tm). Wasim has fallen off the face of the Earth, but I've seen with my own two eyes a working copy of the Iaxy from Digium, so this holds promise. My request for a 1u 24-port IAX-based box that takes Digium daughterboards (FXO or FXS) generated some interest when a show of hands was asked for at the VON show... Bob Knight seemed to have an interest and some time on his hands. ;-) >3) A Radius CDR report module This sort-of exists now, but again is not a completely robust solution. I've not implemented...

I saw that Digium now has a 4 port FXS card. Any plans to add a 4 port FXO card? Gene

...answers and you get one high pitched screech and the line goes dead. On channel 4 it works fine with cidsignalling=v23 and cidstart=polarity enabled. Is this an oddity to do with my hardware layout? I seem to recall a previous posting which suggested that the TDM400P card doesn't like an fxo daughterboard in the first physical slot. Did I recall that correctly? Any suggestions would be most welcome. Many thanks, George

...o another, copied all the config files, and now the LED on the line 11 - third line of the third card doesn't go on (it used to on the previous computer). I can get by telling * not to use this line for now but does anyone have any suggestions for getting it to work? Unseat and reseat the daughterboard? Call Digium for support? /etc/zaptel.conf contains: fxoks=1-11 fxsks=12-16 loadzone = us defaultzone=us -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. MailScanner thanks transtec Computers for their support.

...load(56% lower). The periodic tests that we have done over the last month confirmed these results, that all things being equal, the Sangoma server performed 30-50% more efficiently at doing the same job. I am currently awaiting a beta test version of the Digium TE406P card(with the echo-canceller daughterboard) and I am awaiting word from Sangoma on testing their newly announced A104d card(with on-board echo-canceller) to see how they both fare in our real-world tests. MATT---

Hi List, I am looking for 1U firewall hardware, any ideas? Something like that (http://www.applianceshop.eu/index.php/firewalls/opnsense/opnsense-pfsense-ghz-19-appliance-1.html) but at least with 5GBit nics and more memory. -- Eero

I've just acquired a Unitek ALPHA 1200 Sx UPS to replace an older serial UPS that's been working well with NUT for years. Could anyone with a Unitek tell me what the pinout on the 10P10C plug is so I can make up a cable? Thanks.

asterisk 1.4.35 dahdi 2.3.0.1+2.3.0 one span on a 4port T1 card Got complaints this morning that outbound and inbound calls were "scratchy" and I made a few test calls. It kind of sounds like the gain is too high somewhere, and the audio is overdriven. Is this a problem at the carrier? I'm trying to call them now, but it's Sunday morning in the sticks, and my chances of

Please chime in if you've ever wished for digium to make a 4-port daughter board with a combination of 2FXO AND 2FXS ports on the same card. When using the 800 series cards, one must either choose 4-port permutations of FXS/FXO, OR one must give up 2 valuable ports. In other words, when you add ONE 100-series daughter board, you give up TWO of your physical ports. Is there a technical

Hello I have a Grandstream GXP2000 with latest firmware. When I use it holding the handpiece I don't hear any echo - neither does other end. However, if I use it handsfree, the other end notices echo when they speak - ie their voice is echoy. I hear their voice being a bit echoy. Is this purely down to the IP Phone? Is there anything I can do about it? I considered buying a more

I've seen the embedded posts. Is anyone running Asterisk on the MINI ITX? James Taylor MetroTel 3505 Summerhill Road Suite 11 Texarkana, Tx 75503 903-793-1956

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

I need to build up a few servers and routers, and am wondering how FreeBSD 9.1 is shaping up. Will it be likely to be more stable and robust than 9.0-RELEASE? Are there issues that will have to wait until 9.2-RELEASE to be fixed? Opinions welcome. --Brett Glass

...versatile_init(ram_size, boot_device, kernel_filename, kernel_cmdline, diff --git a/hw/vexpress.c b/hw/vexpress.c index 3596d1e..36503d6 100644 --- a/hw/vexpress.c +++ b/hw/vexpress.c @@ -467,25 +467,27 @@ static void vexpress_common_init(const VEDBoardInfo *daughterboard, arm_load_kernel(arm_env_get_cpu(first_cpu), &vexpress_binfo); } -static void vexpress_a9_init(ram_addr_t ram_size, - const char *boot_device, - const char *kernel_filename, - const char *kernel_cmdline,...

Hi all, these are the remaining unapplied patches of the ARM HDLCD patch series. Changes in v7: - rebased on b61ed421d2c85b5b106c63f2c14f8aa162b282f0; - turn more printk and panic into early_printk and early_panic. Changes in v6: - rebased on 77d3a1db3196b1b5864469f8d3f41d496800c795; - remove useless initializations to NULL in lfb_init; - more compact checks in lfb_init. Changes in v5: - move